사이트 설정

창고
언어 설정
통화 설정
리소스
비디오 라이브러리
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

SCS Series

SMT Current Sense Transformers

RoHS 준수
  • Senses current up to 30 Amps
  • Designed for use between 2 kHz to 1 MHz and above

지금 구매:
개수 단품 가격
1 $5.72
200 $4.29
400 $2.58
1200 $2.01
2400 $1.72

대량 또는 비재고 품목의 경우, 견적서를 요청하십시오.

. 재고 보유 중, 당일 발송 가능.
샘플 신청:

사양

Electrical specifications at 25°C.

부품 번호 1
(Hover for schematics)
인덕턴스
최소 (mH) 2
DCR max (Ω) 3 권수비 전압시간적
(V-µs) 4
주파수 (kHz) 5 전류 (A) 6 종단
저항 RT (Ω) 7
절연
전압 (Vrms) 8
Pri Sec Pri : Sec
SCS-050L_ 3.8 0.0024 0.90 1 : 50 80 6 >1000 30.0 1.7 500
SCS-100L_ 14.8 0.0024 1.8 1 : 100 160 3 >1000 30.0 3.3 500
SCS-200L_ 59.2 0.0024 3.9 1 : 200 320 2 >1000 30.0 6.7 500
메모
  1. When ordering, please specify packaging code: e.g. SCS-200LD
  2. Inductance measured between secondary pins at 10 kHz, 0.06 Vrms, 0 Adc.
  3. Primary DCR is measured with the windings connected in parallel.
  4. Volt-time product is for the secondary, between pin 5 and 6.
  5. For specific questions regarding frequency range, please contact us at [email protected].
  6. Input current of 30 A causes approximately 25°C temperature rise above 25°C ambient when primary windings are connected in parallel. Higher current causes a greater temperature rise (see Temperature Rise vs Current curve).
  7. Terminating resistance (RT) value is based on 1 Volt output with 30 Amps flowing through the primary. Varying terminating resistance increases or decreases output Voltage/Ampere according to the following equation:
    RT (Ohms) = Vout × Nsec / Iin.
  8. 500 Vrms, one minute isolation (hipot) winding to winding.

종단 처리:

  • RoHS-compliant, halogen free. 260°C compatible. Matte tin over nickel over phos bronze terminations.

패키지:

  • D = 13″ machine-ready reel. EIA-481 embossed plastic tape (200 parts per full reel). Quantities less than full reel available: in tape (not machine ready) or with leader and trailer ($25 charge).
  • B = Less than full reel. In an effort to simplify our part numbering system, Coilcraft is eliminating the need for multiple packaging codes. When ordering, simply change the last letter of your part number from B to D.
환경
환경:
RoHS 준수
주변 온도 범위:
–40°C to +125°C
보관 온도 범위:
Component: –40°C to +125°C
Tape and reel packaging: –40°C to +80°C
고장 비율(FIT) / 평균 고장률(MTBF):

성능 곡선

Temperature vs Current

회로도

scss.gif

물리적 특성

scsd.gif

dims_inches_mm.gif

테이프 및 릴 사양

tapereel_pl.gif

 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
13" (330 mm) A B C D E W P Po P1 H T part_or_ao.gif
200 330 100 13 38,4 32,4 32 24 4 2 3,0 0,5

일반 사양

코어 소재:
Ferrite
중량:
3.4 – 3.7 g
패키지:
200/13″ reel Plastic tape: 32 mm wide, 0.5 mm thick, 24 mm pocket spacing, 3.0 mm pocket depth

납땜/세척

수분 민감도(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
납땜 열 내성:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
납땜 전에 Coilcraft 부품의 납땜을 참조하십시오.
PCB 세척:
Tested with pure water or alcohol only. More info.

관련 제품 시리즈